Spec
Material: Main body 100% polyester, sweatband 100% polyester
Size: One size
Depth approx. 17.5cm (when laid flat), visor length approx. 6cm, head circumference approx. 59cm (adjustable with elastic)
*Product size may vary by ±1cm. Please be forewarned.
When worn, it will expand slightly.
Weight: Approx. 47g
Country of origin: Japan
Material
The main body of the cap is made of 100% nylon material, Toray's Stunner®, which is water-repellent, windproof, and permeable. It prevents discomfort caused by sweating while preventing rain and wind, and has excellent durable water-repellent properties.
This product uses COOL DOTS®, which has 4-way stretch (stretches vertically and horizontally).
COOL DOTS® is a high-performance material developed by Komatsu Matere Co., Ltd., made of 100% polyester with countless fine air holes, and has excellent stretchability and breathability.
"Breathability and water repellency"
Excellent breathability is achieved by a special weaving method that opens countless tiny holes (micropores).
It maintains excellent breathability from the inside of the shirt while suppressing the sense of transparency when worn.
[Breathability]
Test method: JIS-L-1096 A method (Brazil method) → 59.6
[Water repellency]
Test method: JIS-L-1092 spray method → Grade 4
"Stretchability and lightness"
Two types of special stretch yarn with different shrinkage rates are used to achieve high stretchability in all directions 360°. Not only is it light at 104g/㎡, but it also has high wrinkle resistance. It quickly recovers its shape even if it is shoved into a backpack pocket and crumpled.
[Stretch recovery rate and stretch rate (%)]
Test method: JIS-L-1096 B-1 method, B method 14.7N
Stretch rate → Vertical 31.9, Horizontal 16.6
Stretch recovery rate → After 30 seconds Vertical 74.9, Horizontal 86.7
[Wrinkle resistance]
Test method: JIS-L-1059-1 Monsanto method 5N
Length direction → 85
Width direction → 78
Wrinkle resistance rate (%)
"Quick-drying and UV protection"
Quick-drying function, which is important when hiking, has become commonplace, and of course this fabric also has it. In addition, it also has UV protection.
[UV measurement (%)]
Test method: JIS-L-1925
Shielding rate Measurement wavelength 280mm-400mm → 96.8
"Durability"
Friction test with the fabric in a dry and wet state.
[Friction (grade)]
Test method: JIS L 0849 (Type II) Dry friction grade 4-5, wet friction grade 4-5 (maximum grade 5)
Part of the stretch system uses plant-derived yarn, Lycra T400® fiber.
Design
The most distinctive feature of this hat is the shape of the brim.
Normal hats have an average brim opening, but this "Enough Hat" has three brim openings: front, side, and back.
The front has a curved shape like a cap's bill. The sides are open just enough to cover the ears. The back is also set short so that it is not too open and is not affected by the wind.
It can be worn in several ways.
When there is little sunlight or if you want to ensure a wide view ahead, raise the front of the brim.
If you raise the back of the brim, you can wear it like a cap or a Tyrolean hat.
COOLMAX® fabric is used for the sweatband.
Made of 100% polyester with a pique pattern, it has the functions of moisture absorption, quick drying, and UV protection (UPF 40+).
If the size of the product is larger than your head size (head circumference) or in a situation where it is easily affected by wind, you can adjust the size by pulling the plastic tab on the back and tightening the rubber.
Size Guide
*The finished size of the product may vary by about ±1cm. Please note.
It will spread slightly when you actually wear it.
If you compare the Basic Cap and the Enough Hat, you will feel that the Enough Hat is slightly shallower.
This is because the brim of the Enough Hat is angled so that it does not touch your ears as much as possible, as shown in the image above.
The Cap can be worn deep up to the ears, but the Hat has an angled brim, so it has to be set shallower.
